Thanks to this script I'm able to produce side-by-side stereoscopic 3d that I use as input for my Sony hmz-t1. This thread describes this workaround in detail: Don't actually use that resolution, keep your monitors at 1280x720. The disadvantage, however, is that the rendering canvas will be scaled, not resized, when hiding the window decorations, so your anti-aliasing will lose some quality (unless you have AA disabled, in which case you will gain some anti-aliasing).įor example, if you have 2 monitors with 720p each (=1280x720), create a custom resolution for 2559x719. With tools such as AutoHotKey you can get rid of these decorations, and have a fullscreen image. Start the app with that resolution (windowed, not fullscreen!), and the resulting window will fill the available space as good as possible (except for the window decorations/borders/title bar). Once this resolution is defined, it is available to Unity's resolution dialog. The trick is to create a custom resolution (with the nvidia control panel) that is 1 pixel less than your desired wide resolution. Note, besides DualHead2Go and ATI EyeFinity / nvidia Surround, there is a tweak which allows Unity to render fullscreen to a wide desktop, which you can then display using the "normal" Windows DualView/multiple Displays setup. Doing that properly does take time and an audio editor.Concerning Side-by-Side rendering for passive stereo: Once you have the file on the PC you can make an audio CD. The advantage of this is you can adjust the audio levels and also record from cassettes, open reel tape decks, and even 8-track players. I bought a device from Ion ( ) several years ago which will accept either high level inputs from a stereo receiver or amp or low level inputs from a TT and outputs a digital signal to a USB cable. I would not use the headphone jack unless it is the only possible connection. If you have a stereo receiver or amp with “phono” inputs, connect the TT to these inputs and use the “tape out” jacks with the adapter cable mentioned in the above paragraph. If the TT output cables are hard wired, you would need two RCA female connectors wired to the stereo plug. If you have a TT with a “high level” output available you would purchase a cable with 2 RCA plugs wired to a 3.5 mm stereo plug to connect to the high level sound card input if available. If it is a “bare” TT you will need a preamp designed for this purpose because the output of the TT needs to be properly equalized to match something called the RIAA curve. I had old computer hooked up to receiver with turntable to record music and need help to hook to windows 10. I just went to to look for one of these cables, but a search on “attenuating” produced no results. You could tell if one was an attenuating cable, because one end of the cable was red. It worked perfectly, because the cable “attenuated” (reduced) the signal going from the library sound system to my tape recorder. I used an attenuating cable to connect from the headphone jack (in the library sound system) to the microphone jack (in my tape recorder). When I was a music major (a very long time ago!), I used to bring my tape recorder to the library so I could record music I was required to listen to. It reduces the signal for you, so as to prevent distortion in the recording and damage to the recorder. That’s where an attenuating cable comes in handy. With this set up you need to adjust the amplifier volume to a very low level to prevent bad things happening to your PC. Connect “headphone out” on the amplifier to “line in” on your PC with a converted cable, 6.5 stereo to 3.5 stereo plug. Longer lengths are available for convenience, but I like shorter to keep signal losses downĢ. But make sure you see all these connections before buying a cable. If you already have a receiver then there are likely two RCA plugs exclusively for the turntable phono inputs, and then you would plug into again likely RCA outputs to a 3.5mm “line in” (hopefully stereo). You will likely need these assuming the turntable has RCA connectors and you will use your PC’s 3.5mm “line in” in the back.įor free app I’d use Audacity to record. A used receiver with one might be better. Others can be bought that have a USB out or a line out. Some modern turntables come with them built in (and usually plug directly into a USB port). The same way: Through a receiver that has a phono preamp.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |